Moog WERKSTAYY-01 Manual de usuario

ASSEMBLY INSTRUCTIONS& USER’S MANUALAnalog Synthesizer / Moogfest 2014 Kit

103) INSTALLING THE ELECTRONICSA) Carefully remove the Printed Circuit Board from the protective sleeve. Take the washer you prepared in the previo

114) POWER / LED TESTUsing only the included power supply, connect the barrel end to the power sup-ply input of your Werkstatt; connect the other end

12FEATURES AND CONTROLSTheWerkstattisamonophonic(onenoteatime)analogsynthesizer,andaswithmanyanalogsynthesizers,theWerkstattismodu

13VCO (VOLTAGE CONTROLLED OSCILLATOR)The Oscillator is the primary sound generating component of an analog synthe-sizer.Basedonthesamecircuitrya

14VCF (VOLTAGE CONTROLLED FILTER) VCA (VOLTAGE CONTROLLED AMPLIFIER) CUTOFF (CUTOFF FREQUENCY KNOB) TheCutoffknobspeciesthefrequencywheretheF

15VCO MOD (MODULATION OF THE VOLTAGE CONTROLLED OSCILLATOR)SOURCE (SOURCE SWITCH)ThisswitchallowsyoutochoosewhichModulationSourcewillbeappl

16VCF MOD (MODULATION OF THE VOLTAGE CONTROLLED FILTER)SOURCE (SOURCE SWITCH)ThisswitchallowsyoutochoosewhichModulationSourcewillbeapplied

17LFO MOD (LOW FREQUENCY OSCILLATOR)RATE (RATE KNOB)Thespeed,orfrequency,oftheLFOiscontrolledviathisknob.TheredLEDwillashonceforev

18ENVELOPE (ENVELOPE GENERATOR)SUSTAIN (SUSTAIN SWITCH)Inasimplesense,theSustainswitchallowsyoutochooseeitherapiano-likebehavior,orsom

19KBD (KEYBOARD)Thisdiagramshowshowthe“button”keyboardoftheWerkstatt(above)re-lates to a standard piano keyboard. Although the note names s

IMPORTANT SAFETY INSTRUCTIONSWARNING - WHEN USING ELECTRIC PRODUCTS, THESE BASICPRECAUTIONS SHOULD ALWAYS BE FOLLOWED.1. Read these instructions.2.

20PATCH (PATCHABLE HEADER)Unlikefullymodularanalogsynthesizersthathavepatch points on every module, the Werkstatt has gathered these inputs and

21REAR PANELThe Werkstatt’s rear panel features two connection points; one audio out-put, and one power jack.AUDIO OUTPUTTheWerkstatt’ssingleaudio

22Tocalibrate,playthelowestnoteonthekeyboard,andsettheVCOFREQknobtothecenterposition.Senda0VsignaltotheVCOEXPINpatchpoint

23STUDYING THE WERKSTATT’S ANALOG CIRCUITSThe Werkstatt circuitry was designed to invite exploration and study of its analog circuits. The complete sc

24SCHEMATIC DOWNLOAD AGREEMENT BY DOWNLOADING THE WERKSTATT SCHEMATIC, YOU ARE AGREEING TO THE FOLLOWING TERMS:1. All copyrights to the circuit dia

SPECIFICATIONSAllSpecicationssubjecttochangewithoutnotice.SOUND SOURCE:VCO - VOLTAGE CONTROLLED OSCILLATORRange:  0to+5VoltSignal;8Hz~

MODULATION SOURCES:LFO - LOW FREQUENCY OSCILLATORRange: + 2.5 VoltControllers: RATE knob:  ModulationFrequency(.2Hz~600Hz) WAVE switch:

Audio Inputs: VCF AUD IN: Filter Audio Input (Un-buffered/Un-mixed  ACcoupled)Control Voltage Outputs: KB CV OUT (x2): Nominal 0.3V/semiton

WARRANTY AND SERVICE INFOLIMITED WARRANTYMoog Music warrants that its products will be free from defects in materials andworkmanship,andshallconfo

Note:Specicationssubjecttochangewithoutnotice.Moog®, and Werkstatt-Ø1® are registered trademarks of Moog Music Inc.©2014 Moog Music IncMOOGMUS

NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limi

TABLE OF CONTENTS INTRODUCTION 6ANALOG SYNTHESIZER BASICS 7ASSEM BLY Parts List 8 Instructions 9WERKSTATT FEATURES AND CONTROLS DefaultSettings

5WERKSTATT- Ø1The Moog Werkstatt-Ø1 is a patchable, 100%analogsynthesizerwhosedesignis based on classic Moog circuits. Assembly is extremely simp

7ANALOG SYNTHESIZER BASICSAnanalogsynthesizergeneratestwotypesofsignals:AudioSignalsandControlSignals.Audiosignalsarethesoundsyouhe

8ASSEM B LYPutting together your Werkstatt is easy. No soldering is required, and all of the electronic components have been pre-assembled. The only t

9INSTRUCTIONS1) ATTACHING THE FEETAttach the four rubber feet by pushing them into the holes of the Bottom Chassis and twisting.The black nylon washer